Skip to main content

Unboxing and Installation

This document guides you through unboxing, installing, and performing the initial configuration of the SuperDock automated drone Dock.

Prerequisites​

1. Initial Configuration​

1.1 Network Check​

Important: After powering on, contact the supplier's engineer to verify that the network is working properly. Only proceed with the following steps after confirmation!

1.2 Connect to the Dock Wi-Fi​

  1. Find the Wi-Fi information

    • Locate the Wi-Fi password label where the device's top cover opens
    • Record the Wi-Fi name and password

  2. Connect the device

    • Use a phone, tablet, or computer to search for the Dock Wi-Fi
    • Enter the password to connect to the network
    • Confirm the connection is successful

1.3 Access the Control Interface​

  1. Open a browser
  2. Navigate to: 192.168.110.201:3000
  3. Wait for the page to finish loading

1.4 On-Site Operation Configuration​

Note: Do not open the Dock's top cover while performing the following operations.

1.4.1 RTK Calibration​

  1. Click the "On-Site Operation" menu
  2. Click "Start RTK Calibration"
  3. Wait for the calibration to complete
  4. Confirm that the feedback message is received: SVIN finish

1.4.2 Mechanical Function Test​

Test whether the following functions execute properly:

  • Open the dock cover
  • Release the push rods
  • Clamp the push rods
  • Close the dock cover

1.4.3 Aircraft Placement​

  1. Open the dock cover

    • Open the dock cover through the control interface

  2. Place the aircraft correctly

    • Arrow markings surround the landing pad
    • The aircraft heading (gimbal end) should point in the direction indicated by the arrows
    • The aircraft tail (battery side) should face the side of the Dock
    • Make sure the aircraft is placed stably

1.4.4 Power Function Test​

Test the following functions in sequence:

  1. Power on the aircraft
  2. Start charging
  3. Stop charging
  4. Power off the aircraft
  5. Click "Restart Dock"

1.5 System Restart Verification​

  1. Wait for the restart to complete

    • The Wi-Fi will disconnect during the restart
    • Reconnect to the Dock Wi-Fi

  2. Confirm the status

    • Return to the home page to check the system status
    • Take a screenshot to save the home page information
    • Send the screenshot to the supplier's engineer for confirmation

2. MQTT Configuration​

2.1 Access the MQTT Configuration​

  1. Connect to the Dock Wi-Fi
  2. Navigate to 192.168.110.201:3000 in your browser
  3. Click the "Reset/Write MQTT" button

2.2 View the Current Configuration​

Enter the MQTT information page to view the information of the currently connected MQTT server

2.3 Switch the MQTT Server​

  1. Reset MQTT

    • Click "Reset MQTT"
    • Wait one minute and then refresh the page

  2. Enter the new server information

    • Enter the MQTT server address
    • Enter the organization ID and organization secret
    • Click "Submit"

  3. Verify the connection

    • Wait one minute
    • Observe whether the MQTT server receives messages

2.4 Switch to the Manufacturer's Server (Optional)​

  1. Click "Set Up Cloud Access"
  2. Wait one minute and then log in to the system

3. Wayline Import​

3.1 Wayline Preparation​

  1. Make sure the pilot has completed wayline planning
  2. Verify the feasibility and safety of the wayline
  3. Prepare the wayline file

3.2 Import Operation​

  1. Select "Wayline Management" in the control system
  2. Upload the wayline file
  3. Verify the wayline parameters
  4. Save the wayline configuration

4. First Flight Test​

4.1 Test Preparation​

  • Operator: The supplier's engineer is the primary operator
  • Supporting personnel: On-site deployment personnel observe and assist
  • Safety check: Confirm that the flight area is safe

4.2 Test Procedure​

  1. System self-check
  2. Aircraft pre-check
  3. Wayline verification
  4. Takeoff test
  5. Wayline flight
  6. Return-to-home and landing

4.3 Test Records​

  • Record flight data
  • Record any anomalies
  • Archive photos/videos

Frequently Asked Questions​

Q1: What should I do if the Wi-Fi connection fails?​

A1:

  1. Confirm that the Wi-Fi password was entered correctly
  2. Check that the device has powered on properly
  3. Try restarting the device and reconnecting

Q2: Cannot access 192.168.110.201:3000?​

A2:

  1. Confirm that you are connected to the Dock Wi-Fi
  2. Check whether your browser is supported
  3. Try clearing the browser cache

Q3: RTK calibration fails?​

A3:

  1. Confirm that the GPS signal is good
  2. Check the antenna connection
  3. Contact technical support

Q4: Mechanical actions are abnormal?​

A4:

  1. Check for any foreign objects blocking the mechanism
  2. Confirm that the power supply is normal
  3. Contact technical support